CNC Milling Vietnam

Precision CNC Milling Service in Vietnam
3-Axis · 4-Axis · 5-Axis

Engineering teams that need milled parts — brackets, housings, plates, complex contoured components — submit drawings to VNcontX and receive CMM-verified parts in 7–12 days. Three-axis to full 5-axis simultaneous milling on DMG Mori equipment. Tolerance held to ±0.005mm standard, ±0.003mm precision. Surface finish to Ra 0.8μm standard or Ra 0.4μm fine. Every order ships with a 100% FAI report and CMM dimensional data. ISO 9001:2015. No deviation. No exception.

CNC milling operation with coolant flood — precision milling service Vietnam | VNcontX
±0.005mm Standard Tolerance
Cpk ≥ 1.67 Process Capability
7–12 Days Standard Lead Time
100% FAI CMM Report Every Order

3-Axis, 4-Axis, 5-Axis — Which Setup Your Part Requires

Axis count is not a marketing label — it directly determines what geometries are achievable, how many setups your part needs, and where tolerance stack-up risk enters. The table below maps part geometry to the correct milling configuration used at VNcontX.

Configuration
Geometry Handled
Typical Tolerance
Common Applications
3-Axis
Flat, prismatic, pocketed parts — tool moves X/Y/Z only
±0.005mm
Plates, brackets, enclosures, flanges
4-Axis
Rotational + linear — part rotates on A-axis while cutting
±0.005mm
Shaft slots, radial features, cam profiles
5-Axis Indexed
Multi-face access in one setup — repositioned, not simultaneous
±0.005mm
Complex housings, valve bodies, aerospace brackets
5-Axis Simultaneous
Full contour milling — all 5 axes move at once
±0.003mm
Impellers, turbine blades, medical implants, compound curves

Equipment: DMG Mori 5-axis for complex geometry. Mazak QT mill-turn for combined milling and turning operations. Inspection: Zeiss Contura CMM + Mitutoyo surface profilometer on every production lot.

Materials Stocked for CNC Milling

Material selection directly affects cutting parameters, tool wear, and achievable surface finish. All materials below are sourced with full CO/CQ traceability documentation — included as standard on every shipment.

Aluminium 6061-T6 · 7075-T6 · 5052 High machinability. 6061 general-purpose; 7075 for high-strength aerospace/structural applications.
Stainless Steel 303 · 304 · 316 · 316L · 17-4 PH 316L for corrosion-critical parts; 17-4 PH for high-hardness precision components.
Carbon & Alloy Steel 1018 · 4140 · 4340 · A36 4140/4340 for high-stress structural and tooling applications.
Titanium Grade 2 · Grade 5 (Ti-6Al-4V) · Grade 23 Grade 5 for medical and aerospace. Slow feed rates; full toolpath verification prior to cutting.
Engineering Plastics POM (Delrin) · PEEK · PC · ABS · PA6/PA66 PEEK for high-temp/chemical resistance; POM for bearing surfaces and wear components.
Brass C360 · C260 · C464 C360 free-machining brass for fittings, connectors, and electrical components.

Surface Finish After Milling

As-milled surface finish on aluminium runs Ra 0.8μm standard. Fine finishing passes achieve Ra 0.4μm. Post-milling surface treatments applied in-house or through Verified Partner Network — all finishing inspected before shipment.

Anodize Type II & III (MIL-A-8625F) Electroless Nickel (ASTM B733) Passivation (ASTM A967) Black Oxide (MIL-DTL-13924) Chem Film Hard Chrome Bead Blast Powder Coat Electropolish Mirror Polish Laser Marking

Finishing spec is confirmed during DFM review — before material is cut. No rework surprises at shipment.

What Engineering Teams Ask Before Placing a First Order

How do I know your tolerances hold across a full production run, not just the first article?

Cpk ≥ 1.67 is verified and documented on every production lot — not just the FAI sample. In-process inspection is run at defined intervals using Zeiss Contura CMM. If a dimension drifts outside control limits, the lot stops. No deviation passes to shipment.

We’ve had DFM feedback that added weeks to our timeline. How does VNcontX handle this?

DFM review is completed within 24 hours of drawing submission. Feedback is returned as a marked-up PDF with specific change recommendations — not a vague hold. If the drawing is production-ready, cutting starts the same business day. No unnecessary review loops.

Can you mill titanium and PEEK to the same tolerances as aluminium?

Yes, with adjusted cutting parameters. Titanium Grade 5 and PEEK are milled at reduced feed rates with verified toolpaths. Tolerance target remains ±0.005mm standard. CMM report on every lot regardless of material — the Zero-Defect Protocol does not change by material type.

What’s the minimum order quantity for CNC milling?

No minimum order quantity. VNcontX runs single FAI samples through to 2,400-unit production lots on the same equipment and inspection process. Prototype pricing and production pricing are quoted separately — request a quote with your drawing and required quantity.

FAQ — CNC Milling Vietnam

What file formats do you accept for CNC milling orders?
STEP (.stp/.step) is preferred for 3D geometry. IGES, DXF, and DWG are accepted. PDF 2D drawings are required alongside any 3D file — they carry the GD&T callouts, surface finish notes, and material specifications that drive the machining program. Incomplete drawing packages delay DFM review; complete packages start the same business day.
What is the tightest tolerance achievable for CNC milling at VNcontX?
±0.003mm on precision features using 5-axis simultaneous milling. Standard production tolerance is ±0.005mm across all axis configurations. Features requiring tighter than ±0.003mm are evaluated case-by-case during DFM — geometry, material, and feature location all affect what is achievable and repeatable at Cpk ≥ 1.67.
How long does a CNC milling order take from drawing submission to shipment?
Standard lead time is 7–12 business days from drawing approval to shipment. Expedited lead time is 5–7 days. FAI samples for approved drawings can ship in 3–5 days. Lead time begins after DFM sign-off — not after order placement. Submit drawings early; DFM review is free and completed within 24 hours.
Is ISO 9001 certification current, and does it cover CNC milling specifically?
ISO 9001:2015 certification is current and covers the full production scope including CNC milling, turning, inspection, and finishing. Certificate is available on request. The QMS governs material traceability, in-process inspection intervals, non-conformance handling, and corrective action. Cpk/Ppk data is retained per lot and available for customer audit.
Can VNcontX handle both prototype milling and volume production from the same drawing?
Yes. The FAI sample is machined on production-intent tooling and cutting parameters — not a one-off prototype setup. When the FAI is approved and you scale to production, the same program, fixturing, and inspection plan runs. No re-qualification required. Production quantities from 10 to 2,400+ units are handled on the same DMG Mori equipment with Cpk-monitored outputs.

Ready to Source CNC Milling from Vietnam?

Submit your drawing. DFM review within 24 hours. Quote same day.
Full CNC machining capabilities →

Request a Technical Quote → Talk to an Engineer →

Direct line: (+84) 906 214 789  ·  duc.nguyen@vncontx.com